针织电脑横机-毛衣机 52寸 12G基本介绍 
 

   针织电脑横机      12G，针板幅宽 52英寸=132cm 
 
 
   
 
 
 

    
 
 
 针织电脑横机-毛衣机 52寸 12G性能特点 
 

   8段选针，10.4英寸LED显示器，全提花，F4000系统，公司引进的日本高精度插片双面磨床为立式结构，是目前国内电脑横机生产厂家  正在使用的设备，其上、下磨头垂直安装在同一轴心线上，由数控编程，其加工精度可达0.002mm。 
  
 
 
 针织电脑横机-毛衣机 52寸 12G技术参数 
 

                  
  
 
 
 针织电脑横机-毛衣机 52寸 12G使用说明 
 

    
 

     
 
 
 
 
  安装环境  
 
 
 
 
  ①温度：摄氏  
  0~35  
  度  
 
 
 
 
  ②湿度：相对湿度  
  3 
  0﹪ 
  ~80 
  ﹪  
 
 
 
 
  ③注意事项  
 
 
 
 
  请勿将机器安装在阳光直射或靠近热源的场所，如暖炉或散热器。  
 
 
 
 
  请勿将机器安装在温度变化过快或很潮湿的场所。  
 
 
 
 
  请勿将机器安装在靠近冷气、暖气或通风设备的出风口位置。  
 
 
 
 
  请勿将机器安装在有化学烟雾或海风吹拂的场所。  
 
 
 
 
  请勿将机器安装在充满灰尘和污垢的场所。  
 
 
 
 
  请勿将机器安装在容易受到震动的场所。  
 
 
 
 
  请勿将机器安装在斜坡或不平的场所。  
 
 
 
 
  安装方法  
 
 
 
 
  以  
  LXC-121  
  系列为例， 
  LXC-252  
  系列安装方法同  
  LXC121  
  系列  
 
 
 
 
  ① 将机器放置在随机附送的垫块上，调整水平，并确保每个垫块均被调节螺丝压牢。  
 
 
 
 
  ② 将纱架升高到正常的工作高度（天线台距置纱板不少于  
  5 
  0 ㎝）并锁紧螺丝，将天线自停装置传输  
 
 
 
 
  线的插头连接好。  
 
 
 
 
  ③将机器用地线接地。  
 
 
 
 
  
 
   电力要求  
  
 
  
 
   电源为电压 220V，频率 50HZ 的交流电，电压波动范围小于 10﹪，电压波动若大于 10﹪时，必须使  
  
 
  
 
   用稳压器。 
  
 
  
 
   
1Power and environmental conditions:
 
   
10%, must be equipped with power voltage.
 
   
Power into line according to provisions of fixed and safety protective measures, can't bear any reaction.
 
   
The equipment must be connected grounding wires, grounding bad will cause personnel electrical shock and affect the safety and reliability of the products of the operation.
 
   
Prohibit direct input/output loop controller insulation test, otherwise will directly cause electrical equipment damage.
 
   
't debris piled up, so as to facilitate the heat dissipation and should be regularly clean dust.
 
   
Stop the operation of electric equipment in damp, dust, corrosive gas, inflammable and explosive gas place, otherwise it may cause personnel electric shock or fire.
 
   
2 Comply with the following specification when make machine maintenance or machine repair:
 
   
Forbid unprofessional person check and repair, avoid to expand the fault even causing injuries and property losses.
 
   
Prohibit the electrical professionals to electrical parts repair, commissioning, avoid to reduce the safety equipment performance, expand the fault even causing injuries and property losses.
 
   
When the machine is running,, must ensure that in the situation of power, to ensure operation safety of personnel.
 
   
Malfunction should by professional personnel to check and repair, and follow this manual repair norms.
 
   
Change control cabinet inside of electrical components, must ensure that in the situation of power, to ensure operation safety of personnel.
 
   
Instead of using the company provides the spare parts, extremely easy to cause fire, electrocution and seriously damaged consequences.
 
   
Please strictly according to the product specification replacing the fuse the marked, so as to ensure the safety of personnel and property.
 
   
. 
 
   
11 After machine maintenance, please keep the parts have been moved  back to correct position.
 
   
12 In order to keep machine running well,. 
 
   
13  Please stop machine run before machine parts test in a power-on state, and adjust to the relevant test menu, then start the test work.
 
   
3 Machine operation should observe followed specification :
 
   
 
    
Don’t opera     chine before understand  machine well.
 
    
Before starting the machine machine at boot, please pay attention to machine the periphery other personnel, prevent the occurrence of harm!
 
    
Operator with lone hair must put the hair up,and ensure hair no hanging during the work , avoid your hair be nipped by the machine carriage in running state. 
 
    
Don’t wear the cloth or jewelry with thin and long accessory ,avoid be nipped by the machine carriage in running state.
 
    
Before starting the machine machine at boot, please check the needle bed knitting pressure ruler, choose sutural pressure ruler and choose sutural whether is in the correct position to ensure that each a medal for knitting and choose the pins were pressure feet, and choose the pins pinned the tail not bulge needle bed 0.5 mm!
 
    
Second-ranking machine run , the operation of the carriage might hit the operators and make it hurt!
 
    
When machine running abnormally, please stop machine, and consult our service person.
 
    
Second-ranking machine in energized, forbidden to open the back part of the electrical box machines, lest electric shock risk!
 
    
Don’t use machine when thunderstorm weather, avoid machine damaged.
 
    
Avoid machine long time running unattended .
 
   
 
  
 
 
 
 
 
 针织电脑横机-毛衣机 52寸 12G采购须知 
 

  价格随汇率，材料费等实际情况波动，下单前请详询，否则订单为无效订单。