免烘烤金属丝印油墨 免烘烤系列
价格
面议
订货量
≥1
最小起订量
≥1
供货总量
100000公斤
产地
江苏省/苏州市
发货期
自买家付款之日起1天内发货
凯贤实业(上海)有限公司

凯贤实业(上海)有限公司

身份认证
主营产品:
PP免处理油墨,PE免处理油墨,自干金属油墨,电镀表面油墨
- 产品参数 -
商标 欧莱斯
型号 MPL
规格 1公斤
包装 按订单
产量 10000
是否有现货
品牌 欧莱斯
着色力
适用对象 金属,玻璃,陶瓷,电镀,不锈钢,白铁,铝
单件净重 1000g
保质期 24
粘度 1000S
流动度≥ 10
颜色 黑白红黄绿蓝等
型号 MPL
规格 1公斤
商标 欧莱斯
包装 按订单
特点 耐酒精,耐汽油,耐酸碱,耐化学品
印刷方式 丝印移印网印
- 产品详情 -

免烘烤金属丝印油墨销售厂家!


本产品主要用于各种金属、玻璃、真空电镀、水电镀、电泳、阳极氧化铝、电解板、铝塑板、喷塑、喷粉、静电喷漆面、烤漆面以及各种天花吊顶氧化板、镜面板、覆膜板、辊涂板等制品的丝印及移印。
油墨特性:
1、平光、附着力佳、耐汽油、耐化学品;
2、手感好,流平性佳、面光洁;
3、表面硬度好,耐冲击性能强、抗刮伤;
4、耐汽油、耐酒精、耐化学品程度佳;
印刷:
选用网目为100-350目,以120T网纱计算涂覆盖面积每公斤达30~35㎡。
表干时间自然挥发5-15分钟,实干时间在24小时以内,48小时后达 性能。
1.用配套专用稀释剂开油水
2.用718洗网水洗网。
3.或添加配套硬化剂10%可增加附着力,提高墨膜硬度。
4.烤箱80℃烘烤10分钟佳能 。
测试方法(完全干燥后):
1.3M胶纸粘在画有百格的油墨表面45度角迅速拉起不脱油。

使用方法:
1.建议用我公司专用稀释剂进行稀释,不建议使用783慢干稀释剂稀释,使用前应充分搅拌,用后随时密封。
2.搅拌时加本公司配套开油水10-12%,稀释到印刷适合粘度,移印稀释使用移印专用稀释剂;用718洗网水清洗。
3.不得与其它类型油墨混合使用,否则容易出现其他附着力,化学反应等不良现象。
4. 加入固化剂的油墨使用时限为8小时,过期请弃用,剩余油墨不可回收
注意事项:
1.各种承印物料的外观相似,但可能会是不同的材料,客户需先试印,确其符合要求后,再批量生产。
2.在移印过程中,如出现拉丝或散开,可适当加入一些慢干膏即可;
3.环境温度过高,将会影响油墨原有质量。白色超越150都会变色,烘烤时请用木质材料垫底进行烘烤,不得直接接触铁
4.根据气候变化,请远离火源,阴暗处15度-30度环境下存放
Brand: but MY name: anodic oxidation INK Numbers: 65496 
Anodic oxidation ink series 
The product is produced with advanced import acrylic resin and senior pigment after fine grinding system, used in combination to ABS, PP, PET, all kinds of metal, glass, ceramic, stone, electroplating (water cut electroplating), anodic alumina surface and roast (spray paint products of screen and pad printing, not needing curing agent, and does not need to , can obtain excellent adhesion. 
Ink characteristics: 
1 the classification includs glass, adhesion, good resistance to gasoline, alcohol, resistance to chemicals; 
2, feel is good, flow ping sex, good surface is bright and clean; 
3 and fine surface hardness, impact resistance properties of strong, resistance to scratch; 
4, resistant to gasoline, alcohol, resistant to chemicals resistant degree good; 
Printing: 
Choose for 100-350 mesh mesh to 120 T nets yarn with coverage area calculation per kilogram of 30 to 35 ㎡. 
Dry time table natural volatilize 5 to 15 minutes, action in time within 24 hours, after 48 hours of optimum performance. 
, open oil and water 
718 net. 
10% supporting can increase adhesion, improve ink film hardness. 
80 ℃ for 10 minutes Canon even better. 
Test method (dry) : 
1.3 M tape stuck in the picture has's ink surface 45 degree Angle quickly pull up not to take off oil. 
99% alcohol 500 G force in ink surface wipe 300 times back and forth without decoloring. 
Method of use: 
, not recommended dry thinners diluted 783 slow, before the use should be fully mixing, use at any time after sealing. 
10 to 12%, oil and water dilute the printing for viscosity, pad printing dilution use moving printing special thinner,; Use clean water to wash the nets 718. 
, otherwise easy to have other adhesion, chemical reactions and other bad phenomenon. 
8 hours, please not used, the remaining expired ink not recycling 
Note: 
, but may be of different material, customers are required to meet the requirements of the ShiYin, indeed, its, then batch production. 
, such as a wire drawing or away, can be appropriately to add some slow dry paste can; 
,, roasted beyond 150 when please use woodiness material bottom, and may not directly contact roast iron 
, please away from fire, the shadows 15 degrees-30 degrees environment for


 

 

您还可以搜索
朋友圈二位码

长按二维码,保存至相册。
发送给微信好友。